Linux version 2.6.25.4-norhtec-sis (root@norh) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #4 Fri Oct 3 10:03:42 CEST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ec000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000007800000 (usable)
 BIOS-e820: 00000000ffe80000 - 00000000ffef0000 (reserved)
 BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
120MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Entering add_active_range(0, 0, 30720) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    30720
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    30720
On node 0 totalpages: 30720
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 208 pages used for memmap
  Normal zone: 26416 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
Allocating PCI resources starting at 10000000 (gap: 07800000:f8680000)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30480
Kernel command line: root=/dev/hda1 ro quiet
No local APIC present or hardware disabled
mapped APIC to ffffb000 (010f2000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 2048 bytes)
Detected 200.009 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 118012k/122880k available (1836k kernel code, 4400k reserved, 864k data, 276k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffb9000 - 0xfffff000   ( 280 kB)
    vmalloc : 0xc8000000 - 0xfffb7000   ( 895 MB)
    lowmem  : 0xc0000000 - 0xc7800000   ( 120 MB)
      .init : 0xc03a6000 - 0xc03eb000   ( 276 kB)
      .data : 0xc02cb3c2 - 0xc03a3660   ( 864 kB)
      .text : 0xc0100000 - 0xc02cb3c2   (1836 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay using timer specific routine.. 401.33 BogoMIPS (lpj=802661)
Security Framework initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: vendor_id 'SiS SiS SiS '
Compat vDSO mapped to ffffe000.
CPU: SiS 550 stepping 05
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 0k freed
net_namespace: 444 bytes
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb61, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f8b40
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x7cab, dseg 0xf0000
PnPBIOS: 9 nodes reported by PnP BIOS; 9 recorded by driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS [1039/0018] at 0000:00:01.0
NET: Registered protocol family 8
NET: Registered protocol family 20
system 00:01: iomem range 0x0-0x9fbff could not be reserved
system 00:01: iomem range 0x9fc00-0x9ffff could not be reserved
system 00:01: iomem range 0xf0000-0xfffff could not be reserved
system 00:01: iomem range 0x100000-0x77fffff could not be reserved
system 00:01: iomem range 0xffe80000-0xffeeffff could not be reserved
system 00:01: iomem range 0xfffc0000-0xffffffff could not be reserved
PCI: Bridge: 0000:00:02.0
  IO window: b000-bfff
  MEM window: 0xdfd00000-0xdfefffff
  PREFETCH window: 0x00000000cfa00000-0x00000000dfbfffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1223060792.259:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux agpgart interface v0.103
agpgart: Detected SiS chipset - id:1360
agpgart: AGP aperture is 8M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
brd: module loaded
loop: module loaded
8139too Fast Ethernet driver 0.9.28
PCI: setting IRQ 5 as level-triggered
PCI: Found IRQ 5 for device 0000:00:0d.0
eth0: RealTek RTL8139 at 0xd800, 44:4d:50:e2:a7:81, IRQ 5
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller (0x1039:0x5513 rev 0xd0) at  PCI slot 0000:00:00.1
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS550 ATA 100 (1st gen) controller
SIS5513: IDE port disabled
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: CF CARD 1GB, ATA DISK drive
hda: applying conservative PIO "downgrade"
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO1
hda: MWDMA2 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 1949472 sectors (998 MB) w/1KiB Cache, CHS=1934/16/63
 hda: hda1
 hda: p1 exceeds device capacity
Driver 'sd' needs updating - please use bus_type methods
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:01.2
ohci_hcd 0000:00:01.2: OHCI Host Controller
ohci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:01.2: irq 11, io mem 0xdfff7000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usb 1-1: new full speed USB device using ohci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-3: new full speed USB device using ohci_hcd and address 3
usb 1-3: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
I2O subsystem v1.325
i2o: max drivers = 8
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
cpuidle: using governor ladder
Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC).
PCI: setting IRQ 10 as level-triggered
PCI: Found IRQ 10 for device 0000:00:01.4
ALSA device list:
  #0: SiS7019 Audio Accelerator with ALC202 at 0xdc00, irq 10
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 276k freed
scsi 1:0:0:0: Direct-Access     USB 2.0  Flash Disk       5.00 PQ: 0 ANSI: 2
scsi 0:0:0:0: Direct-Access     WDC AC34 000L             0000 PQ: 0 ANSI: 0
sd 0:0:0:0: [sdb] 7814016 512-byte hardware sectors (4001 MB)
sd 1:0:0:0: [sda] 8227840 512-byte hardware sectors (4213 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sdb] Write Protect is off
sd 0:0:0:0: [sdb] Mode Sense: 27 00 00 00
sd 0:0:0:0: [sdb] Assuming drive cache: write through
sd 0:0:0:0: [sdb] 7814016 512-byte hardware sectors (4001 MB)
sd 1:0:0:0: [sda] 8227840 512-byte hardware sectors (4213 MB)
sd 0:0:0:0: [sdb] Write Protect is off
sd 0:0:0:0: [sdb] Mode Sense: 27 00 00 00
sd 0:0:0:0: [sdb] Assuming drive cache: write through
 sdb:<5>sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 0b 00 00 08
sd 1:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 1:0:0:0: [sda] Attached SCSI removable disk
 sdb1
sd 0:0:0:0: [sdb] Attached SCSI disk
usb-storage: device scan complete
usb-storage: device scan complete
attempt to access beyond end of device
hda: rw=0, want=1969479, limit=1949472
Buffer I/O error on device hda1, logical block 246176
attempt to access beyond end of device
hda: rw=0, want=1969479, limit=1949472
Buffer I/O error on device hda1, logical block 246176
attempt to access beyond end of device
hda: rw=0, want=1969631, limit=1949472
Buffer I/O error on device hda1, logical block 246195
attempt to access beyond end of device
hda: rw=0, want=1969631, limit=1949472
Buffer I/O error on device hda1, logical block 246195
attempt to access beyond end of device
hda: rw=0, want=1969631, limit=1949472
Buffer I/O error on device hda1, logical block 246195
attempt to access beyond end of device
hda: rw=0, want=1969575, limit=1949472
Buffer I/O error on device hda1, logical block 246188
attempt to access beyond end of device
hda: rw=0, want=1969623, limit=1949472
Buffer I/O error on device hda1, logical block 246194
Real Time Clock Driver v1.12ac
sis630_smbus 0000:00:01.0: SIS630 comp. bus not detected, module not inserted.
EXT3 FS on hda1, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1